Filtering of smokes emissions to comply with european standards
Smoke filtration is a very important item in a combustion system. It is at this level that practically everything is played out, as far as emissions into the atmosphere are concerned. This means, the quantity and size of the particles as well as the type of potentially harmful substances. It is therefore at this level that a combustion system can be made neutral for the environment. It is the smoke filtration that makes a combustion system complying with local or European standards.
Several technologies allow different levels of filtration and are provided to obtain a given emission quality. The choice of technology, or the combination of several technologies, will be based on the composition of the waste and the required level of the quality of the emissions.
INFIGROUP advises and supports you in the choice of your filtration system, depending on the nature of your waste and your emissions quality requirements.
NO ADDITIONAL FILTER
Filtration by the post-combustion
Post-combustion filtration results from the oxidation of gases from the combustion chamber. The dust contained in the fumes is partially eliminated at the same time as the microparticles contained in the fumes. Post-combustion, placed under the combustion chamber, completes the oxidation of fats, a process initiated in the combustion chamber.
- Benefits :
- No cost
- Colourless and odourless fumes
- Disadvantages :
- Remaining dust
- Pollutants largely eliminated
- Fumes rejected at 600°C
DUST COLLECTOR
Filtration cyclone filter
It is a dry filtration method. Located after the post-combustion, the cyclone retains the dust resulting from the incineration which is already oxidized in the postcombustion. They are then sent to a cyclone to recover the remaining dust, by gravity. The chimney is located directly above the cyclone. ✔ Low cost ✔ Colourless and odourless fumes ✘ Still some remaining dust ✘ Remaining pollutants ✘ Fumes rejected at 300°C
- Benefits :
- Colourless and odourless fumes
- Colourless and odourless fumes
- Disadvantages :
- Still some remaining dust
- Remaining pollutants
- Fumes rejected at 300°C
WET SCRUBBER
Wet filtration
The wet scrubber (washer) is located after the postcombustion. The flow of smoke is led to the washer by the Ventury effect. The washer consists of a water injection ramp + reagent (liquid lime), a cyclonic bell and a pool (tank provided for this purpose). The dust resulting from incineration which is already oxidized in the post-combustion is then sent to the wet scrubber. The fumes are sprayed with a «water + reagent» mixture which weighs down the dust and which, by gravity, carries it into the pool. The contaminated water is then analyzed and neutralized to reach a neutral PH of 7. To do this, a dosing pump and a PH analyzer with a probe are directly immersed in the pool. The water + reagent mixture circulates in an open or closed loop. The chimney is located directly above the washer to expel the flow of clean air. For some cases, it is possible to install a double washer, meaning, two washers in series.
- Benefits :
- Cost optimized
- Colourless and odourless fume
- It complies with CE standards in most cases but not certified in continuous for all types of waste
- Disadvantages :
- Very little dust / pollutants remaining
- Fumes rejected at 200°C
FILTRATION BY CERAMIC FILTER
Dry filtration
It is a combination of cyclone + ceramic filters). It is the only one certified 100% CE. Its role is only to regulate the flow of releases from gases if the installation does not works properly (bad regulation of burners, anomaly in oxygen management, etc.). The dust, already oxidized in the post-combustion, is sent to a cyclone in order to remove the remaining dust. The gases are meanwhile cooled, to be treated. The microparticles are captured by the reagents (hydrated lime + activated carbon) injected into the dilution reactor and led to the ceramic filter. The gases temperature drops down as they pass through the different modules. Ceramic filtration removes the few remaining harmful fluxes, through the reactants injected into the reactor, placed between the cyclone and the ceramic filter.
- Benefits :
- 100% complying with CE standards
- Colourless and odourless fume
- Fumes rejected <100°C
- Disadvantages :
- Expensive
Several degrees of filtration
- ZONE 1 FILTRATION BY POST-COMBUSTION (STD MODEL)
- ZONE 2 FILTRATION BY SMOKE WASHER (LVE MODEL) (with one or two washers)
- ZONE 3 FILTRATION BY SCETCH (SC MODEL) (injection of active solution: dehydrated lime liquid in a second pool)
- ZONE 4 FILTRATION BY CERAMIC CANDLES (CRF MODEL)
INFIGROUP's expertise ensures you the best solution, whatever the type of system you have or you need, is :
- BIOMASS BOILERS;
- WASTE INCINERATORS OF ALL BRANDS;
- CREMATION EQUIPMENT OF ALL BRANDS;
- AUTOMATIONS (PLCs) OF ALL BRANDS;
- FILTERS OF ALL BRANDS.
Main avantages
- Recognized and proven competences on all brands
- Knowledge of all manufacturers of cremation equipment, incinerators and filtration
- Flexibility of interventions
- Reliability, fast intervention, and higher time between two maintenance visits, replacements and repairs
